Water Recycle Systems
WRS 12 & WRS 12+ Water Recycle System
The WRS 12 and WRS 12+ Water Recycle Systems are designed to solve wash water disposal problems for the smaller user. These completely automatic treatment systems will collect dirty, oily wash water and process it so that it can be reused in your washing operation. The recycle feed pump transfers the dirty water from a collection sump to the treatment unit. Reagents are added to the water to kill bacteria and odours, neutralize the pH, and remove pollutants such as oil, grease, dirt, and sludge. These reagents, which are commonly used in drinking water treatment, actually make the water much more environmentally friendly and less hazardous for personnel doing the washing. The treated water is then stored in the integral holding tank until needed for washing.
The WRS 12 and WRS 12+ both treat 2 gpm (3000 gpd), which is enough for many washing operations. They are equipped with many convenience features, including automatic priming and degassing valves for the reagent pumps (manual priming valve on coagulant pump), power cord with GFCI and15 amp 115 volt plug, and integral water storage tank. The WRS 12+ is also provided with a fiberglass reagents pumps enclosure, larger inlet strainer with valve-in-head, flow meter, and filters status pressure gauge. Both systems come completely assembled and wired, ready to be set in place and plugged into a 15-amp, 115-volt outlet. The water discharge from the integral storage tank is pressurized to feed your pressure washers, even if they are remotely located. Premium components and quality construction ensure the most trouble-free operation possible.
Specifications
Rated flow:
Recycle feed pump:
2 gpm (3000 gpd)
Electrical requirement:
Self-priming centrifugal cast iron pump with 1/3 HP thermally protected motor. Mounted on the machine base on WRS 12+. Controlled by float switch in collection pit. Suction line strainer and foot valve are provided.
Discharge pump:
115 VAC, 60 Hz, 1 phase, 15 amp total
High head centrifugal pump with 1/2 HP thermally protected motor. Provides pressurized water flow to pressure washer and other uses.
Electrical controls:
GFCI provided, prewired with 15 amp plug, 10 ft cord Lighted switches for power, feed pump, coagulant pump, oxidizer pump, pH adjuster pump, makeup water, and manual drain. pH controller with digital display. NEMA 4 rated enclosure
Reagent metering pumps:
Electronic controlled diaphragm pumps with stroke rate and stroke length controls. Automatic degassing head on oxidizer and pH adjust pump. Manual bleed valve on coagulant pump. Pumps are mounted in a fiberglass enclosure on WRS 12+.
Inlet strainer:
Large size in corrosion resistant plastic housing. Valve-in-head housing on WRS 12+.
Filter system:
20" long 20 micron filter cartridge for final polishing. Two cartridges included with machine.
Sludge collection system:
20" long 20 micron filter cartridge for final polishing. Two cartridges included with machine.
Make-up water:
100 psi maximum pressure. Automatically added as required by application.
Recycle tank capacities:
Connection sizes:
Coagulant tank- 50 gallons.
Recycle construction:
Machine inlet- 1 NPT
Treated water outlet- 3/4 NPT
Drain line- 1 NPT
Make up water- 1/2 NPT
Overall dimensions:
Heavy duty polypropylene tank with unitized construction. Schedule 80 PVC pipe used throughout. Heavy steel base assembly.
Separator tank - 50 gallons
Storage tank - 50 gallons
Total water capacity - 150 gallons
5 ft 9 in long, 2 ft 8 in deep, 4 ft 3 in tall
Shipping Weight:
400 pounds
Options:
Second pH adjusting pump. Additional treated water storage capacity. Activated carbon water polishing systems. Sand filter final polishing system. Pre-treatment systems, oil skimmers, and oily water separators. Ozone treatment. Graduated reagent containers. Custom modifications available.